Jobber Length Drill Bit, Heavy Duty, 7/32 in, 5.56 mm, 0.2188 in

COBALT DRILL BIT 7/32 R10CO

Jobber Length Drill Bit, Silver and Deming, 27/32 in Drill, 0.8438 in Drill, 6 in Lg, 3-1/8 in Dp Cut, Standard Flute, 3-1/8 in Lg Flute, 1/2 in Shank

HI-SPEED DRILL BIT R57 27/32

Jobber Length Drill Bit, Type N, General Purpose, Imperial, 51/64 in Drill, 20.24 mm Drill, 0.7969 in Drill, 152.4 mm Lg, 3 in Dp Cut, 2 -Flute, Spiral Flute

Standard length drill with 1/2 in reduced straight shank, diameter 0.7969 in (51/64) with an overall length of 6 in and flute length of 3 in according to DORMER standard with 118 deg point angle, HSS with steam tempered finish for 4xD drilling without...

Jobber Length Drill Bit, General Purpose, Imperial, Z Drill, 0.413 in Drill, 5-1/4 in Lg, 4XD Dp Cut, 2 -Flute, Spiral Flute, 3-7/8 in Lg Flute, 0.413 in Shank

For general purpose drilling under a wide range of operating conditions and in various materials such as cast iron, steel and steel forgings. The steam oxide finish and surface treatment provide abrasion resistance and improved chip flow. Bits have a...

Jobber Length Drill Bit, Heavy Duty, Imperial, 1/16 in Drill, 1-1/4 in Lg Flute, 135 deg Point

For use in cast iron base and steel base alloys, stainless steels, titanium, etc. These heavy duty bits have a 135 deg split point with a straight shank, and are made of high speed steel. Bits shown below are in fractional measures.

Jobber Length Drill Bit, Imperial, 6 in Lg, 3 in Dp Cut, 2 -Flute, Spiral Flute, 3 in Lg Flute

Standard length drill with 1/2 in reduced straight shank, with an overall length of 6 in and flute length of 3 in accord ing to ANSI standard with 118 deg split po int, HSS with steam tempered + bronze f inish for 4xD drill ing without peck ing in steel.

Jobber Length Drill Bit, General Purpose, Imperial, 6 in Lg, 3 in Dp Cut, 2 -Flute, Spiral Flute, 5/8 to 7/8 in

Jobber length drill with 1/2 in reduced tri-flat shank, with an overall length of 6 in and flute length of 3in according to ANSI standard with 118 deg point angle, HSS with bright + steam tempered finish for 4xD drilling without pecking in steel.

Jobber Length Drill Bit, General Purpose, Heavy Duty, Imperial, 2 -Flute, Spiral Flute, 135 deg Point

For use in cast iron base and steel base alloys, stainless steels, titanium, etc. These heavy duty bits have a 135 deg split point with a straight shank, and are made of high speed steel. Bits shown below are in fractional measures.

Jobber Length Drill Bit, General Purpose, Imperial, 6 in Lg, 3 in Dp Cut, 2 -Flute, Spiral Flute, 1 to 1-3/16 in

Jobber length drill with 1/2 in reduced tri-flat shank, with an overall length of 6 in and flute length of 3in according to ANSI standard with 118 deg point angle, HSS with bright + steam tempered finish for 4xD drilling without pecking in steel.